Conductivity Controller & Transmitter
MODEL : CC 603-1
Display : 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display
Resolution: 0.01μS to 0.1mS (depends on range)
Cell constant : 0.01 / 0.1 / 1 (user selectable depends on range)
- Introduction
- Specifications
- Key Features
Product Details
To measure the ability of water to pass electrical flow through it is known as conductivity of water and directly proportional to the resistance of water. It directly depends on the concentration of conductive ions present in the water. The sources of origin for conductive ions are inorganic metals, such as Chloride, Carbonate, alkalis, Sulfide components and dissolved solids. Which is measured Simens per meter (S/m) in SI units and millimhos per centimeter (mmho/cm) in U.S units.
The CC 603 - 1 series of Conductivity Controller and Transmitter provides a reliable method of Monitoring, Controlling & Transmitting 4 - 20mA / RS 485 MODBUS RTU communication for interfacing to PLC, Data logger, HMI, etc.,. This product is suitable to measure Conductivity in water treatment, Electrolytic water cleaning, Chemical industries, food process, waste water treatment, textile industries & neutralization process, etc.,. This Conductivity Controller & Transmitter can measured using industrial conductivity sensors, temperature can be measured using temperature sensor. This Conductivity Controller & Transmitter has many user friendly and safety features which as follows.
| Model | CC 603-1 |
|---|---|
| Display | 4 + 4 Digit 0.5” & 0.39” 7 Seg RED LED Display |
| Range | 1 - 20μS, 5 - 200μS, 10 to 2000μS, 1 to 20mS, 5 to 200mS |
| Resolution | 0.01μS to 0.1mS (depends on range) |
| Accuracy | ± 1 % of range ± 1 digit |
| Cell constant* | 0.01 / 0.1 / 1 (user selectable depends on range) |
| Temperature sensor | RTD - PT 100 (3 wire) |
| Temperature Co-efficient | 0 to 3 % / ºC (user adjustable) |
| Temperature Compensation | Manual / Automatic (-20.0 to +150.0ºC) |
| Electrode Input | Conductivity cell on rear panel |
| Set Point - 1 & 2 | Two Set Point with 6 Relay Status Selectable |
| Relay Output | Relay - 1 for Setpoint - 1, Relay - 2 for Setpoint - 2 with 5A Rating |
| Relay Hysteresis | 0 to 500 counts (user adjustable) (only for High & Low control modes) |
| Relay Cyclic delay | 0 to 100 seconds (user adjustable) (only for High & Low control modes) |
| Alarm Output (optional) | Inbuilt audible buzzer with front key reset |
| Optional Re. Tx. output | Galvanically Isolated 4 - 20 mA |
| Optional Comm. output | Isolated RS 485 |
| Comm. Protocol | MODBUS RTU |
| Operating Environment | -10 to 50ºC / 10 to 95 % RH Non Condensing |
| Power Supply | 90 to 270V AC / DC 50Hz |
| Dimension | 96 x 96 x 85 mm |
| Cutout Dimension | 92 x 92 mm |
| Weight | 350 grams (Approx.) |
Note: .* cell constant selection for Measuring ranges as follows
1) For 1 - 20μS(Ultra pure & DM water) 0.01 cell constant selectable
2) For 5 - 200μS(Drinking water & other applications) 0.1 cell constant selectable
3) For 10 - 2000μS, 1 - 20mS & 5 - 200mS(raw water, sewage & High range liquids) 1 cell constant only
2. Online Conductivity sensor is Optional. It depends on application, working temperature, type of fitting & cable length
3. Due to continuous product improvements, Published specifications may change with out notice
Economical, easy to calibrate and setup- User selectable 5 ranges from 1μS to 200mS
- High accuracy
- Programmable auto/manual temperature compensation
- Optional isolated RS 485 communication with MODBUS RTU protocol
- Optional galvanically isolated 4 – 20mA output
- Adjustable cell constant for particular ranges
- Manual single or 2 point calibration
- 2 relay outputs with configurable individual H/L setting with 6 relay status
- Optional audible inbuilt buzzer output
- Universal supply voltage 90 to 270V AC/DC
